Can I Set Up a Tub Myself? Considerations And Also Steps
Can I Set Up a Tub Myself? Considerations And Also Steps
Blog Article
This article in the next paragraphs about How to Install a Bathtub Yourself is absolutely enlightening. Check it out yourself and decide what you think about it.
Setting up a bathtub isn't specifically rocket science, but it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably challenging project. If the old bathtub is readily obtainable, the job can move easily; if you have to open up a wall surface to remove the old bathtub and place the new bath tub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will certainly need an assistant to move out the old bathtub and embeded in the new one. Make certain you have certified yourself for the work and fit attempting it. Instead of hiring a specialist to take control of a halfway-completed job, it is far better to think about utilizing one prior to you begin. Opportunities are you may need a specialist plumber to make tube connections.
This post will help you set up a brand-new bathtub in your shower room if you have already acquired a new tub and also don't need to transform the arrangement of your previous water supply pipes.
Your devices and material list should make up the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted gain access to that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the staying water that will originate from the pipelines. As soon as the supply pipelines have actually been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing substance.
Prior to going on to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, then you will require a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washers remain in area in between the tap and the sink. Secure the faucet in position with the maker offered backnut. Once the faucet is firmly in place, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal faucet adapters. The former type needs to be attached to the tap ends initially, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Mounting the Tub
Using both wood boards under its feet, place the bath tub in the needed position. The wood boards are practical in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four little points.
The following goal is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level and changing the feet on the bathtub till the spirit level reviews level.
To install faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipeline by making a compression join; after that do the same for the other faucet.
Switch on the water system and also check all joints as well as brand-new pipework for leaks as well as tighten them if essential. Load the tub as well as also examine the overflow outlet as well as the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the supplier's user's manual. Tiling and also sealing around the bath tub should wait up until the bath tub has been made use of at least once as this will certainly settle it into its last position.
Getting ready for the Installment
Firstly, the sustaining structure provided with the bath should be fitted (if needed) according to the maker's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets device to prevent strain on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you utilize every one of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Tiling Around the Bath tub
In the area where the bath meets the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a stiff seal, triggering the water to permeate the wall in between the bathroom as well as the tiling, resulting in problems with dampness and feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked paper or soft rope. Keep in mind to always fill the tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealer can break fairly very early if you do not take into consideration this motion before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly available on the marketplace. It is a good idea to fit the tiles making use of waterproof or waterproof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm certainly very taken with How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I am praying you enjoyed my entry. Kindly set aside a second to share this blog posting if you enjoyed it. Many thanks for going through it.
Schedule Today
Report this page